TL DNR Types: LOOK at the attached INPA Screens FIRST before you dismiss. It is very powerful, but many/ Most ALL versions I have seen, are in German with LITTLE Translation to English, other than Menus.
Inpa bmw aif reading install#
7-series (F01, F02), 2007+ (only DTC reading)įor BMW E/F Scanner II V2018.12 List of supported ECU:īody – 65 categories / 121 types AHM, AMP, BFH, BFS, BZM, CCC, CDC, CHAMP, CIC, CID, DWA, ECL, FAH, FAS, FLA, FOMO, FRM, FZD, HKL, HUD, IHKA, JBBF, KBM, KGM, KOMBI, LMA, MASK, MMC, MMI, MPM, PDC, PGS, RAD, RFK, RLS, RSE, SASL, SASR, SBSL, SBSR, SD, SECUR, SFZ, SGM, SHD, SHZH, SIM, SSBF, SSFA, SSH, STVL, STVR, SZL, SZM, TEBF, TEFA, TEL, TMB, TMBH, TMF, TMFH, VID, WIM, ZBE, ZGM and etcĭrive – 6 categories / 30 types CAS, DME, EGS, EKPM, GWS, VTG and etcĬhassis – 12 categories / 15 types ASR, CIM, DSC, EDC, EDCSHL, EDCSHR, EDCSVL, EDCSVR, EHC, EMF, RDC, VDM and etcįor BMW E/F Scanner II V2018.12 Software Free Downloadĭifference Between For BMW E/F Scanner I And For BMW EF Scanner II Same:ġ.EF Scanner I out look is the same as EF Scanner IIĢ.EF Scanner I and EF Scanner II support total 166 types of ECUġ.EF Scanner II is much cheaper than EF Scanner IĢ.EF Scanner II work more stable than EF Scanner Iģ.EF Scanner II with newest software V2018.12 and support more new vehicles than EF Scanner I (2013.7)Ģ) Medium configuration for diagnosis.cluster calibration ,oil resetģ) Advanced Full configuration for diagnosis. INPA, is BMW Factory-Level Diagnostic Software included in BMW Standard Tools. Install BMW INPA on WinXP Win7 Win8 Win10 Free Download BMW E-sys V3.22.5 v3.2.61 v3.2.71 Free ECM Titanium 1.61 with 26000 drivers Original wiTech Micropod II vs. From the different pictures and my testing with INPA what I can see is below MAF Sensor Voltage at ignition (engine off) is 0.41V with 4kg/h and Air mass 1. 5-series “Gran Turismo” (F07), 2009+ (only DTC reading)ħ. I found the following sections in the INPA to read the air flow, not sure what it means or does. To my understanding WinKFP, either NCS, and BMW coding tool are all capable of the same things as ISTA/P. ISTA/P is for the programming side of software, but I haven’t installed or used that one. * Not for all ECU’s E-series CAS1, CAS2, CAS3, CAS3+ mileage Reset by OBDĮ/F Scanner II V2018.12 For BMW Supported model list:Ĥ. ISTA/D replaced INPA, and is all around more sophisticated.
Inpa bmw aif reading code#
Reading and adjustment of run hours and maintenance intervals for: Oil, Filters, Brake pads, Spark plugs, Liquids, Inspections and services as well as СО, СН inspections etc.Īdjustment of mileage and maintenance intervalsĬhange/Adjust FA code (currently in test mode) Added line below (see image0 below) to E87.eng, E89.eng, E90.eng.
I found this post and followed the instructions - adding the following to E90 E89 and E87. V2018.12 For BMW E/F SCANNER II BMW Diagnostic + Mileage Adjustmentįor BMW E/F Scanner II V2018.12 Basic Version Features:ĭiagnosis and interpretation of error codes A member here PM'd me and said to choose E89. recommend you new launched for BMW E/F Scanner II for BMW diagnostic and odometer correction. V2018.12 E F scanner 2 suits for BMW cars, Mini Cooper R56 and Rolls-Royce BMW Explorer. For BMW E F Scanner II is the new generation BMW diagnostic tool and odometer correction tool.